9 years ago I had this 1TB Seagate ST31000340AS hard disk that I was using as a primary drive for my OS and also the place to store all my photos, video clips and other important stuff.
At some point it simply failed to work. No strange sounds, no nothing. The BIOS would not recognize it, OS would not see it.
I left it like that for for 6-7 years, but in the last week I started informing myself about how to fix it.
I knew there wasn’t any mechanical issue with it and I was suspecting HDD firmware issues.
And my suspicion was right. There was a known glitch with multiple series of Seagate models, more specific – with their SD15 firmware.
Now the fun begins, because there is a solution to this issue.
- The materials needed to fix:
bricked Seagate HDD
- Torx T6 screwdriver
- USB to UART Prolific PL2303HX convertor cable (3$). link to Amazon. Also found as “PL2303HX USB to UART TTL Cable Module 4p 4 pin RS232 Converter”.
- A postit or a piece of paper, folded 2-3 times or any other slim non electric conductive material.
- Prolific PL2303HX drivers that actually work on Windows 10 (get them from here, not the manufacturer’s website).
- (optional) External HDD rack or connect the HDD directly to your motherboard via SATA and Molex ATX power cable.
Before we start, please be aware that there is a slight possibility that you will lose your data or break your HDD if you are not careful.
If you have important data that you cannot afford to lose, please go to a data recovery company to fix your hard drive.
Start the fixing process:
- power off your PC or your external USB hard disk rack.
- Important: make sure that the SATA or USB cable is disconnected from your PC/external HDD rack.
- Remove any jumpers from the HDD. If you have any.
- Take the Torx T6 screw driver and remove all 6 screws and detach the HDD PCB. Remember that the long screws are always connected on the corners of the HDD.
- Place the folded postit between the PCB and the contacts for the drive head. Leave the drive motor contacts in place. Tighten the three screws closest to the motor contacts. Leave the other three screws loose or removed.
- Install the USB adapter’s drivers (from the link provided at the beginning of the post) and make sure that Windows sees it as COM port in Device manager and you don’t have any yellow errors on it. Reboot if necessary.
- Connect the USB adapter to the PC.
- Go to Device manager and right click>> properties and make the following settings on you new installed USB/COM adapter:
- Choose 38400, 8, None, 1, None in the COM properties box.
You will need to connect 3 wires from the USB adapter to the HDD. The 4th is not used:
- GREEN cable is RX on the USB cable -> connects to TX on HDD
- WHITE cable is TX on the USB cable -> connects to RX on HDD
- BLACK cable is the grounding -> connects to the ground pin on HDD
- You should connect the TX pin of the hard drive to the RX pin of the adapter, and the hard drive’s RX pin to the adapter’s TX pin. This is the theory. In the real life it worked backwards for me.
- Connect the 3 pins like this:
These pins are located next to the hard drive’s SATA connector.
If you can’t fit the pins on the HDD, strip the plastic shielding from the pins.
- After inserting the pins, power on the PC or the external USB rack. The SATA cable should be disconnected from the HDD. Same for the external rack.
(RX, TX and ground pins connected to the HDD)
- Download putty from their official site.
- Open putty and make these settings. Make sure you are using the correct COM port number. Mine was COM8, but it might be different for you. Go to device manager to check the actual port number.
- Baud 38400
- Data Bits 8
- Stop Bits 1
- Parity none
- Flow Control none
- Hit save and open.
- You should see a blank screen. Hit Ctrl+Z.
- If you connected the pins correctly you should see a prompt like this:
If not, you may have the TX & RX wires swapped. Switch the green wire with the white one and try again
Go to Access Level 2 (type /2):
F3 T>/2 (hit enter)
Wait about 30 seconds, then spin down the motor:
F3 2>Z (enter)
Spin Down Complete
Elapsed Time 0.147 msecs
If you instead see a message similar to this:
LED: 000000CE FAddr: 00280D4D
Then you entered the commands too quickly after supplying power to the drive.
Tighten the all screws. Then start the motor:
F3 2>U (enter)
Spin Up Complete
Elapsed Time 7.093 secs
Next go to Level 1 (type /1):
F3 2>/1 (hit enter)
And do a S.M.A.R.T. erase (create S.M.A.R.T. sector):
F3 1>N1 ( hit enter)
When the prompt comes back up, turn off power to the hard drive, wait a few seconds, then turn it back on. Wait about 20 seconds, then finally do partition regeneration:
Note, the command bellow contains Zero, not o – as in order.
F3 T>m0,2,2,0,0,0,0,22 (hit enter)
After 15-30 seconds, you should see something like:
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 14, Max Certify Rewrite Retries = 00C8
User Partition Format 10% complete, Zone 00, Pass 00, LBA 00004339, ErrCode 00000080, Elapsed Time 0 mins 05 secs
User Partition Format Successful – Elapsed Time 0 mins 05 secs
Do not turn off drive until you see this message.
Once seen, drive can be turned off.
Power down everything, place drive back into your computer, and confirm that it’s working.
Update the firmware to the latest version! Google is your friend.